Kilz Original Interior Multi-Purpose Oil-Based Primer/sealer - 1 qt

Kilz original primer is a powerful stain-blocking formula that blocks most heavy interior stains including water, smoke, tannin, ink, pencil, felt marker, grease, and also seals pet, food and smoke odors. Trusted by pros for over 40 years, it has excellent sealing and adhesion properties help paint adhere to most interior surfaces leading to better results. Use on wood, drywall, plaster, paneling, wallpaper, masonry, brick, painted metal and properly prepared glossy surfaces.

Features

• Primer is a powerful stain-blocking formula
• Original may be top-coated with latex or oil-based paint
• Blocks heavy interior stains
• Seals smoke, pet and food odors
• Seals porous surfaces for uniform finish
• Block stains including water, smoke, tannin, pencil, felt marker, grease
• Use on wood, drywall, plaster, paneling, wallpaper, masonry, brick, painted metal and properly prepared glossy surfaces

Surface Preparation

• The following steps are recommended for product performance.
• All surfaces must be clean, free of dust, chalk, oil, grease, wax, polish, mold and mildew, loose peeling paint, rust and all other foreign substances.
• If washing is necessary, use a non-soapy detergent or a tsp substitute, rinse well and allow to dry.
• Glossy surfaces: for maximum adhesion, scuff sand the surface thoroughly before priming.
• Peeling or checked paint: scrape off loose paint and sand to a smooth surface.
• Mold or mildew covered surfaces: wash the area with a mildew remover, rinse with water and allow to dry before priming.
• Masonry, brick, stucco and plaster: kilz original primer may be used on clean, dry, aged masonry surfaces that have cured (dried) at least 90 days. If masonry has cured less than 90 days, use kilz
• premium, kilz 2 or kilz original low odor primers.
• Fire restoration: it is critical to clean smoke damaged surfaces thoroughly before priming.

Application

• Eye Protection Is Recommended. Do Not Thin. Stir Thoroughly Before And Occasionally During Use
• Apply using a brush, roller or sprayer.
• Use product when painting surface and air temperatures are between 35°f (2°c) and 90°f (32°c)
• Brush high quality nylon/polyester
• Roller high quality 3/8-1/2" nap on smooth surfaces or 1/2-3/4" nap on semi-rough or porous surfaces.
• Airless spray .015-.019 tip / 60 mesh filter
• Prime entire surface to ensure a uniform appearance of the topcoat
• Stainblocking: after priming, test for stain bleed-through by applying the topcoat to a small section.
• If the stain bleeds through the topcoat, apply a second coat of primer and test again before topcoating the entire area. If bleeding continues, a longer dry time is needed before topcoating
• Tinting: up to 2 oz of universal colorant per gal. Tinting to a lighter shade than topcoat is recommended
• Coverage: 300-400 sq ft. (28-37 m2) per gal depending on application method and surface porosity

Dry Time

• Dry Time @ 77° F (25°C) / 50% RH: Touch in 30 min.
• Paint In 1 Hr

Clean Up & Disposal

• Clean equipment and paint spatter with mineral spirits or acetone. Immediately after use, dispose of soiled rags and waste in a closed, water-filled container.
• Do not dispose of this product down a drain. Please consider donating any unused product.
• If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with all current federal, state and local regulations. For recycling or disposal information contact your local household refuse collection service.

Warning

This product contains chemicals known to the state of california to cause cancer, birth defects, or other reproductive harm.

First Aid

• If swallowed, do not induce vomiting. Get medical attention immediately.
• If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical attention immediately.
• In case of eye contact, flush eyes immediately with plenty of water for at least 15 min and get medical attention.
• For skin, wash thoroughly with soap and water.

Keep from freezing. If frozen, let thaw at room temperature.

Keep out of reach of children!

Specification

• Size: 1 qt
• Base Type: Oil-Based
• Brush Material: Nylon / Poly
• Color: White
• Coverage: 300 - 400 Sq Ft
• Dry To Recoat: 1 Hr
• Dry To Touch: 30 Min
• Interior/Exterior: Interior
• Maximum Application Temperature: 90°F
• Minimum Application Temperature: 50°F
• Roller - Porous Surface Nap: 1/2" - 3/4"
• Roller - Smooth Surface Nap: 3/8" - 1/2"
• Spray Pressure: 2,500 - 3,000 Psi
• Spray Tip: .015" - .019"
• Viscosity: 80 - 90 KU
• VOC: 443 G/L
• Warranty: Lifetime Warranty