Kilz Original Multi-Purpose Interior Oil-based Primer - 1 gal

New Look, Same Trusted Formula! KILZ Original Primer Is A Powerful Stainblocking Formula That Blocks Most Heavy Interior Stains Including Water, Smoke, Tannin, Ink, Pencil, Felt Marker, Grease And Also Seals Pet, Food And Smoke Odors. Trusted By Pros For Over 40 Years, Excellent Sealing And Adhesion Properties Help Paint Adhere To Most Interior Surfaces Leading To Better Results. Use On Wood, Drywall, Plaster, Paneling, Wallpaper, Masonry, Brick, Painted Metal And Properly Prepared Glossy Surfaces. Not Recommended For Mold Or Mildew-prone Surfaces Or On Flooring.

Features

• Seals Porous Surface
• Promotes Adhesion
• Helps Block/seal Odors
• Helps Block Severe Stains
• Helps Block Light/medium Stains
• Hides Previous Color

Surface Preparation

• The Following Steps Are Recommended For Product Performance
• All Surfaces Must Be Clean, Free Of Dust, Chalk, Oil, Grease, Wax, Polish, Mold And Mildew, Loose Peeling Paint, Rust And All Other Foreign Substances
• If Washing Is Necessary, Use A Non-soapy Detergent Or A TSP Substitute, Rinse Well And Allow To Dry
• Glossy Surfaces: For Maximum Adhesion, Scuff Sand The Surface Thoroughly Before Priming
• Peeling Or Checked Paint - Scrape Off Loose Paint And Sand To A Smooth Surface
• Mold Or Mildew Covered Surfaces - Wash The Area With A Mildew Remover, Rinse With Water And Allow To Dry Before Priming
• Masonry, Brick, Stucco And Plaster - KILZ Original Primer May Be Used On Clean, Dry, Aged Masonry Surfaces That Have Cured (dried) At Least 90 Days. If Masonry Has Cured Less Than 90 Days, Use KILZ Premium, KILZ 2 Or KILZ Original Low Odor Primers
• Fire Restoration - It Is Critical To Clean Smoke Damaged Surfaces Thoroughly Before Priming

Application

• Eye Protection Is Recommended. Do Not Thin. Stir Thoroughly Before And Occasionally During Use
• Apply Using A Brush, Roller Or Sprayer
• Use Product When Painting Surface And Air Temperatures Are Between 35°F (2°C) And 90°F (32°C)
• Brush “ High-quality Nylon/Polyester
• Roller “ High Quality 3/8-1/2" Nap On Smooth Surfaces Or 1/2-3/4" Nap On Semi-rough Or Porous Surfaces
• Airless Spray “ 0.015 - 0.019 Tip / 60 Mesh Filter
• Prime Entire Surface To Ensure A Uniform Appearance Of The Topcoat
• Stainblocking - After Priming, Test For Stain Bleed-through By Applying The Topcoat To A Small Section. If The Stain Bleeds Through The Topcoat, Apply A Second Coat Of Primer And Test Again Before Topcoating The Entire Area. If Bleeding Continues, A Longer Dry Time Is Needed Before Topcoating
• Tinting: Up To 2 Oz Of Universal Colorant Per Gal Tinting To A Lighter Shade Than Topcoat Is Recommended
• Coverage - 300-400 Sq. Ft. Per Gal Depending On Application Method And Surface Porosity

Dry Time At 77°F(25°C), 50% RH

• Dry Time @ 77°F (25°C) / 50% RH: Touch In 30 Minutes
• Paint In 1 h

Clean Up & Disposal

• Clean Equipment And Paint Spatters With Mineral Spirits Or Acetone. Immediately After Use, Dispose Of Soiled Rags And Waste In A Closed, Water-filled Container
• Do Not Dispose Of This Product Down A Drain. Please Consider Donating Any Unused Product
• If Spilled, Contain Material And Remove With An Inert Absorbent. Dispose Of Contaminated Absorbent, Container And Unused Product In Accordance With All Current Federal, State And Local Regulations

Warning

If You Scrape, Sand, Or Remove Old Paint, You May Release Lead Dust. Lead Is Toxic. Exposure To Lead Dust Can Cause Serious Illness, Such As Brain Damage, Especially In Children. Pregnant Women Should Also Avoid Exposure. Wear A NIOSH-approved Respirator To Control Lead Exposure. Clean Up Carefully With A HEPA Vacuum And A Wet Mop. Contains Petroleum Distillates.

Vapor Harmful - May Affect The Brain Or Nervous System Causing Dizziness, Headache, Or Nausea. Causes Eye, Skin, Nose And Throat Irritation.

Use Only With Adequate Ventilation - Do Not Breathe Vapors Or Spray Mist. Ensure Fresh Air Entry During Application And Drying. If You Experience Eye Watering, Headache, Or Dizziness, Or If Air Monitoring Demonstrates Vapor/mist Levels Are Above Applicable Limits, Wear An Appropriate, Properly Fitted Respirator (NIOSH / MSHA TC 23°C Or Equivalent) . Avoid Contact With Eyes, Skin And Clothing. Wash Thoroughly After Handling And Before Smoking And Eating.

Notice - Reports Have Associated Repeated And Prolonged Occupational Overexposure To Solvents With Permanent Brain And Nervous System Damage. Intentional Misuse By Deliberately Concentrating And Inhaling The Contents May Be Harmful Or Fatal.

Vapors May Cause Flash Fire: Vapors Can Flow Along Surfaces To A Distant Ignition Source And Flashback. Keep Away From Heat, Sparks And Flame. Do Not Smoke. Extinguish All Flames And Pilot Lights And Turn Off Stoves, Heaters, Electric Motors And Other Sources Of Ignition During Use And Until All Vapors Are Gone. Prevent Build-up Of Vapors By Opening All Windows And Doors To Achieve Cross-ventilation. To Avoid Spontaneous Combustion, Soak Soiled Rags And Waste Immediately After Use In A Closed, Water-filled Metal Container. See Clean-up And Disposal For More Information.

Keep From Freezing. If Frozen, Let Thaw At Room Temperature. Keep Out Of Reach Of Children.

Specifications

• Color: White
• Size: 1 Gal
• Base: Oil
• Coverage - Low: 300 Sq. Ft.
• Mils Wet: 5.3
• Mils Dry: 2.3
• Coverage - High: 400 Sq. Ft.
• Mils Wet: 4
• Mils Dry: 1.7
• Finish @ 85°: <10
• Application Temperature (min): 5°F (10°C)
• Application Temperature (max): 90°F(32°C)
• Viscosity: 80 - 90 KU
• Dry To Touch: 30 Minutes
• Dry To Recoat: 1 Hr
• Max Tint: 2 oz
• VOC: 443 G/L
• Brush: Nylon / Poly
• Roller - Smooth Surface: 3/8" - 1/2" Nap
• Roller - Porous Surface: 1/2" - 3/4" Nap
• Spray Tip: 0.015" - 0.019"
• Spray Filter: 60 Mesh
• Spray Pressure: 2,500 - 3,000
• Volume Solids: 42.7% (+/-) 2%
• Weight Solids: 63.9% (+/-) 2%
• Flashpoint: 75°F (23.9°C)
• Certification: ASTM D522
• Warranty: Lifetime Limited Warranty

Safety Data Sheet.pdf

Technical Sheet.pdf