Zoom the image with the mouse
Liquid Nails Tub Surround and Shower Adhesive - 10 oz
SKU:
298367
UPC:
022078449994
$5.99
$4.99
(You save
$1.00
)
Liquid Nails Tub Surround & Shower Wall Adhesive (LN-715) provides an exceptional waterproof bond under extreme conditions and won't harm most tub surrounds and shower walls. Light color won't show through surrounds. Recommended for most plastic tub and shower enclosures.
Features
- No burn through
- Heat & Steam resistant
- Great for polystyrene, plastic and fiberglass tub & shower units
- Light color won't show through
Application Instructions
Apply adhesive to surround panel in a 1/4" wide continuous bead approximately one inch from the edges of the panel. An "S" or "X" shaped bead may be applied to the center portion of the panel. Press the panel firmly into place on the wall within 15 minutes of the adhesive application. Repeat for remaining panels and corner units. To develop more tack, peel panels back from wall for 3 minutes, the press back into place. Bracing may be needed if panels do not lie flat. For overlap areas and edges, this adhesive may be used as a caulk. Panel edges and seams may be caulked after 24 hours. Allow adhesive and caulk to dry overnight prior to use.
It is important for proper installation that each panel be vented according to the following directions. Venting method: Apply LN-715 adhesive and press panel firmly to wall, then pull away. Wait 3-5 minutes, then press panel firmly back into place. For proper adhesion, after 20-30 minutes go around entire tub surround and press firmly over all flat surfaces. If any edges lift up, tape them to the wall with masking tape until adhesive dries. Let cure 24 hours.
Specifications
- Size: 10 oz
- Coverage: 32 Lineal ft. Using 1/4" Bead
- VOC: < 7% By Wt. (< 70 G/L)
- Certifications: ASTM C-557
- Warranty: Limited Warranty
Liquid Nails Tub Surround & Shower Wall Adhesive (LN-715) provides an exceptional waterproof bond under extreme conditions and won't harm most tub surrounds and shower walls. Light color won't show through surrounds. Recommended for most plastic tub and shower enclosures.
Features
- No burn through
- Heat & Steam resistant
- Great for polystyrene, plastic and fiberglass tub & shower units
- Light color won't show through
Application Instructions
Apply adhesive to surround panel in a 1/4" wide continuous bead approximately one inch from the edges of the panel. An "S" or "X" shaped bead may be applied to the center portion of the panel. Press the panel firmly into place on the wall within 15 minutes of the adhesive application. Repeat for remaining panels and corner units. To develop more tack, peel panels back from wall for 3 minutes, the press back into place. Bracing may be needed if panels do not lie flat. For overlap areas and edges, this adhesive may be used as a caulk. Panel edges and seams may be caulked after 24 hours. Allow adhesive and caulk to dry overnight prior to use.
It is important for proper installation that each panel be vented according to the following directions. Venting method: Apply LN-715 adhesive and press panel firmly to wall, then pull away. Wait 3-5 minutes, then press panel firmly back into place. For proper adhesion, after 20-30 minutes go around entire tub surround and press firmly over all flat surfaces. If any edges lift up, tape them to the wall with masking tape until adhesive dries. Let cure 24 hours.
Specifications
- Size: 10 oz
- Coverage: 32 Lineal ft. Using 1/4" Bead
- VOC: < 7% By Wt. (< 70 G/L)
- Certifications: ASTM C-557
- Warranty: Limited Warranty
Related Products
