null Skip to main content
Zoom the image with the mouse
Compare Colors Compare Colors

Rust-Oleum Specialty Appliance Epoxy Spray Paint - 12 oz

SKU: 775155-P
UPC: 020066788186
$9.99 - $11.99

Rust-Oleum specialty appliance epoxy is an ultra-hard, moisture resistance enamel that is specifically formulated for indoor metal surfaces. It provides a smooth, washable surface for refinishing the exterior of appliances such as refrigerators, dishwashers, laundry machines and other indoor metal applications (cabinets, tables). Do not use on objects exposed to heat (stovetops, oven interiors, etc).

Features
  • Indoor use only
For Best Results

Spray on 2-3 light coats a few min apart; no primer needed.

Application

Apply only when air and surface temperatures are between 50-90°F (10-32°C) and the relative humidity is below 85% to ensure proper drying. Avoid spraying in very windy or dusty conditions. Cover the surrounding area to protect from overspray. Overspray can carry a significant distance. Shake can vigorously for one minute after mixing ball begins to rattle. If mixing ball fails to rattle do not strike can. Contact rust-oleum. Shake often during use. Hold can upright 10-16" from the surface and spray in a steady back-and-forth motion, slightly overlapping each stroke. Keep the can the same distance from the surface. Keep the can in motion while spraying. Apply 2 or more light coats a few minutes apart to avoid runs and sags. Do not use near open flame.

Dry and Recoat Times

Dry and recoat times are based on 70ºF (21°C) and 50% relative humidity. Dries tack-free in 2-4 hr and can be handled in 5-9 hr. Recoat within 30 min or after 1 week.

Clogging

If valve clogs, twist and pull off spray tip and rinse it in a solvent such as mineral spirits. Do not insert any object into can valve opening.

Cleanup

Clean valve immediately after use by turning can upside down and depressing spray button for 3-5 seconds (some paint will be sprayed out, so be careful to not inadvertently spray yourself or other objects). Clean up wet paint with xylene or mineral spirits. Throw away empty can in trash pick-up. Do not burn or place in the home trash compactor.

Surface Preparation

Remove all dirt, grease, oil, salt and chemical contaminants by washing the surface with a commercial detergent or other suitable cleaning method. Rinse with freshwater and allow to thoroughly dry. Remove loose paint and rust with a wire brush or sandpaper. Previously coated surfaces must be sound and in good condition. Smooth, hard or glossy finishes should be scarified by sanding to create a surface profile.

Warning

If you scrape, sand or remove old paint from any surface, you may release lead paint dust. Lead is toxic. Exposure to lead dust can cause serious illness, such as brain damage; especially in children. Pregnant women should also avoid exposure. Wear a niosh approved respirator to control lead exposure. Clean up carefully with a hepa vacuum and a wet mop.

Specifications
  • Size: 12 oz
  • Resin Type: Epoxy Ester Modified Alkyd
  • Solvents: Acetone, Toluene, VM&P Naphtha, Xylene
  • Dry Heat Resistance: 200°F (93°C)
  • Flash Point: -156°F (-104°C)

Safety Data Sheet.pdf

Safety Data Sheet.pdf

Technical Date Sheet.pdf

Choose Options:
 

Rust-Oleum specialty appliance epoxy is an ultra-hard, moisture resistance enamel that is specifically formulated for indoor metal surfaces. It provides a smooth, washable surface for refinishing the exterior of appliances such as refrigerators, dishwashers, laundry machines and other indoor metal applications (cabinets, tables). Do not use on objects exposed to heat (stovetops, oven interiors, etc).

Features
  • Indoor use only
For Best Results

Spray on 2-3 light coats a few min apart; no primer needed.

Application

Apply only when air and surface temperatures are between 50-90°F (10-32°C) and the relative humidity is below 85% to ensure proper drying. Avoid spraying in very windy or dusty conditions. Cover the surrounding area to protect from overspray. Overspray can carry a significant distance. Shake can vigorously for one minute after mixing ball begins to rattle. If mixing ball fails to rattle do not strike can. Contact rust-oleum. Shake often during use. Hold can upright 10-16" from the surface and spray in a steady back-and-forth motion, slightly overlapping each stroke. Keep the can the same distance from the surface. Keep the can in motion while spraying. Apply 2 or more light coats a few minutes apart to avoid runs and sags. Do not use near open flame.

Dry and Recoat Times

Dry and recoat times are based on 70ºF (21°C) and 50% relative humidity. Dries tack-free in 2-4 hr and can be handled in 5-9 hr. Recoat within 30 min or after 1 week.

Clogging

If valve clogs, twist and pull off spray tip and rinse it in a solvent such as mineral spirits. Do not insert any object into can valve opening.

Cleanup

Clean valve immediately after use by turning can upside down and depressing spray button for 3-5 seconds (some paint will be sprayed out, so be careful to not inadvertently spray yourself or other objects). Clean up wet paint with xylene or mineral spirits. Throw away empty can in trash pick-up. Do not burn or place in the home trash compactor.

Surface Preparation

Remove all dirt, grease, oil, salt and chemical contaminants by washing the surface with a commercial detergent or other suitable cleaning method. Rinse with freshwater and allow to thoroughly dry. Remove loose paint and rust with a wire brush or sandpaper. Previously coated surfaces must be sound and in good condition. Smooth, hard or glossy finishes should be scarified by sanding to create a surface profile.

Warning

If you scrape, sand or remove old paint from any surface, you may release lead paint dust. Lead is toxic. Exposure to lead dust can cause serious illness, such as brain damage; especially in children. Pregnant women should also avoid exposure. Wear a niosh approved respirator to control lead exposure. Clean up carefully with a hepa vacuum and a wet mop.

Specifications
  • Size: 12 oz
  • Resin Type: Epoxy Ester Modified Alkyd
  • Solvents: Acetone, Toluene, VM&P Naphtha, Xylene
  • Dry Heat Resistance: 200°F (93°C)
  • Flash Point: -156°F (-104°C)

Safety Data Sheet.pdf

Safety Data Sheet.pdf

Technical Date Sheet.pdf